 |
CONTRACTOR AUDIO LINKS:
Tel: 0800 043 4600
|
Contractor audio sales - Amplifiers To buy any items please call sales on 0800 043 4600
|
||
| |
AUSTRALIAN MONITOR AMIS 120P AMPLIFIER The AMIS120P is a 120 watt power amplifier with outputs for 4 and 8 ohms, 70 and 100 volt line. It may be desk or rack mounted. The AMIS120P features a flat screwdriver accessible gain control on the rear panel. This amplifier features a status LED. The amplifier may operate from mains power or 24V DC. Power Output 120 Watts RMS Maximum Load 80 Ohms @ 100 Volts Power Bandwidth 60Hz - 15kHz < 0.5% THD Frequency Response 60Hz - 15kHz (± 3dB) Total Harmonic Distortion 0.5% @ 1kHz rated power Signal To Noise Ratio -80dB Input Sensitivity 700mV Outputs 100V, 70V, 4 Ohm, 8 Ohm Controls One gain control on rear of the unit via flathead screwdriver control Indicators Power "on" LED Power Source AC 230/240V - 50Hz; DC 24V; 110V - 60Hz (special) 3 pin IEC connector Power Consumption 300 Watts Protection Current Limiter protection, plus AC and DC fuses Dimensions/Weight 88mm H x 480mm W x 280mm D (Chassis Dimensions only). 12kg Rack Mounting Standard |
£ Please phone EACH EX VAT & DELIVERY |
| |
AUSTRALIAN MONITOR AMIS 250P The AMIS250P is a 250 watt power amplifier with outputs for 4 ohms, 70 and 100 volt line. It may be desk or rack mounted. The AMIS250P features a flat screwdriver accessible gain control on the rear panel. The amplifier may operate from mains power or 24V DC. AMIS250P Specifications Power Output 250 Watts RMS Maximum Load 40 Ohms @ 100 Volts Power Bandwidth 60Hz - 15kHz < O.5% THD Frequency Response 60Hz - 15kHz (± 3dB) Total Harmonic Distortion 0.5% @ 1 kHz rated power Signal To Noise Ratio -80dB Input Sensitivity 700mV Outputs 100V, 70V, 4 Ohm Controls One gain control on rear of the unit via flathead screwdriver control Indicators Power "on" and "Protect" LED Power Source AC 230/240V - 50Hz; DC 24V; 110V - 60Hz (special) 3 pin IEC connector Power Consumption 400 Watts Protection Current Limiter protection, plus AC and DC fuses Dimensions/Weight 88mm H x 480mm W x 330mm D (Chassis Dimensions only). 15kg Rack Mounting Standard |
£ Please phone EACH EX VAT & DELIVERY |
| |
AUSTRALIAN MONITOR AMIS 480P AMPLIFIER The Australian Monitor Installation Series AMIS480P is a robust, highly featured 4 channel power amplifier. Offering 4 independent channels, each delivering 80 watts into 4 ohms or 70/100 volt line, the AMIS480P is designed to operate in extreme conditions to give the contractor the most reliable 4 channel amplifier available today. AMIS480P Specifications Power Output (1% THD, all channels driven) 4 x 80W Freq. Response (1W) 80Hz - 20kHz Power Bandwidth (-3dB) 85Hz - 20kHz THD (1kHz, -3dB) Less than 0.5% S/N Ratio 94dB (ref 100V) Crosstalk 1kHz 80dB; 20Hz - 20kHz Better than 60dB Input Sensitivity 0.775V RMS (0dBu) Input Impedance 20KO Voltage Gain (pot at max) 100V out 129 (42dB); 70V out 90 (39dB); 4O out 23 (27dB) Output Regulation (1kHz) 95% Dimensions (h x w x d) 88mm x 483mm x 432mm (4.36" x 19" x 17") Weight 20kg (44lb) Shipping Dimensions (h x w x d) 230mm x 540mm x 550mm (9.1” x 21.3” x 21.7”) Shipping Weight 24kg (53lb) |
£ Please phone EACH EX VAT & DELIVERY |
| |
AUSTRALIAN MONITOR AMIS 1202P AMPLIFIER The AMIS1202P is a dual channel 120W + 120W power amplifier designed to deliver continuous full range performance in a compact and reliable package. The AMIS1202P is two independent amplifiers in the one chassis making it the perfect choice for multi-zone or multi-channel applications. The amplifier may operate from mains power or 24V DC. AMIS1202P Specifications Power Output 120 Watts per channel Maximum Load 80 Ohms on 100 Volt line setting Frequency Response 50Hz - 15kHz (± 3dB) Total Harmonic Distortion 0.5% at 1kHz (1 Watt - full power) Signal To Noise Ratio -80dB at 100V; -80dB at 8 Ohms; -80dB at 4 Ohms Input Sensitivity 0.5 Volt RMS - 100 Volt line Input Impedance 10K Ohms Input Connection Active balanced input with male and female 3 pin XLR input/output sockets per channel. Outputs 100/70 Volt line and 4/8 Ohm via rear panel barrier strip. Line out to feed additional amplifiers from one of the paralleled XLR input sockets Controls Front panel power switch; Recessed rear panel input attenuator (per channel) Metering/Indicators Signal-present LED per channel Power Source AC 230/240V - 50Hz; DC 24V; 110V - 60Hz (special) 3 pin IEC connector Power Consumption 400 Watts (maximum) Protection Fuses for overload and short circuit protection, High temperature trip (disconnects load at 120¼C), DC Output Sensing (disconnects load if DC is present) Dimensions/Weight 88mm H x 483mm W x 315mm D (Chassis dimensions only). 15kg Rack Mounting Standard |
£ Please phone EACH EX VAT & DELIVERY |
| |
AUSTRALIAN MONITOR DCM500 AMPLIFIER The DCM500 is a high performance 500 watt power amplifier designed to meet the needs of the most demanding sound reinforcement installations and applications. The amplifier is designed to operate from both AC mains power as well as 24 volts DC. DCM500 Specifications Power Output 500 Watts RMS into 100 & 70 Volt line or 4 Ohms Maximum Load 20 Ohms @ 100V Frequency Response 50Hz - 15kHz (± 3dB) into 100V Total Harmonic Distortion Less than 0.5% @ 1kHz; Distortion at Max Power: 0.7% Signal To Noise Ratio -82dB Input Sensitivity Max 300mV (set @ 1V) Input Impedance 10K Ohms Input Connection Transformer Balanced input with male and female XLR input/output sockets Outputs 100 & 70 Volts or 4 Ohm speaker outputs via a rear panel barrier strip. Line out to feed additional power amplifiers available from 1 of the paralleled XLR inputs Controls Front Panel Power Switch, Recessed front panel input attenuator Metering/Indicators Amplifier Status Display Window including: Power On LED; 10 segment LED output meter; Mains fail LED; High temp trip LED Power Sources AC: 240V - 50Hz or 110V - 60Hz 3 pin IEC connector; DC: 24V with built in trickle charge circuit: 300ma maximum trickle charge 30 Amp maximum current draw on DC 300ma standby (idle) current draw on DC Power Consumption 800 Watts (maximum) Protection Internal Cooling Fan with temperature sensor Compressor/Limiter Current Limiter with auto protect and auto reset Dimensions/Weight 88mm H x 483mm W x 410mm D (Chassis dimensions only). 18 kg |
£ Please phone EACH EX VAT & DELIVERY |
| |
QSC ISA SERIES AMPLIFIERSDesigned as a cost-effective solution specifically for sound contractors, the ISA Series features seven models including four low impedance models (ISA 280, ISA 450, ISA 750, ISA 1350) rated for 2-ohm operation, and three "Ti" versions with isolated 25, 70 and 100 volt outputs for distributed audio systems (ISA 300Ti, ISA 500Ti, ISA 800Ti). Versatile loading options and a comprehensive feature set make the ISA Series a rugged, cost-effective power solution for any permanently installed sound system. Unique among distributed sound power amplifiers, the "Ti" versions will drive 8 or 4 ohm loads and a distributed system on the same channel simultaneously. This enables a contractor to reduce the number of required amplifier channels by allowing a limited number of distributed speakers to be attached to the same amp as is powering the main sound system. |
|
| |
QSC ISA 280 2 x 280W @ 4 Ohms power amplifier with rear gain controls • STEREO MODE, Both Channels Driven 8 ohms 20 Hz-20 kHz 0.1% THD 185W 4 ohms 20 Hz-20 kHz 0.1% THD 280W 2 ohms 1 kHz 1% THD 430W • BRIDGE MONO MODE 8 ohms 1 kHz 0.1% THD 600W 4 ohms 1 kHz 1% THD 830W |
£ Please phone EACH EX VAT & DELIVERY |
| |
QSC ISA 450 2 x 425W @ 4 Ohms power amplifier with rear gain controls • STEREO MODE, Both Channels Driven 8 ohms 20 Hz-20 kHz 0.1% THD 260W 4 ohms 20 Hz-20 kHz 0.1% THD 425W 2 ohms 1 kHz 1% THD 700W • BRIDGE MONO MODE 8 ohms 1 kHz 0.1% THD 900W 4 ohms 1 kHz 1% THD 1400W |
£ Please phone EACH EX VAT & DELIVERY |
| |
QSC ISA 750 2 x 650W @ 4 Ohms power amplifier with rear gain controls • STEREO MODE, Both Channels Driven 8 ohms 20 Hz-20 kHz 0.1% THD 450W 4 ohms 20 Hz-20 kHz 0.1% THD 650W 2 ohms 1 kHz 1% THD 1200W • BRIDGE MONO MODE 8 ohms 1 kHz 0.1% THD 1500W 4 ohms 1 kHz 1% THD 2400W |
£ Please phone EACH EX VAT & DELIVERY |
| |
QSC ISA 1350 2 x 1300W @ 4 Ohms power amplifier with rear gain controls • STEREO MODE, Both Channels Driven 8 ohms 20 Hz-20 kHz 0.1% THD 800W 4 ohms 20 Hz-20 kHz 0.1% THD 1300W 2 ohms 1 kHz 1% THD 2000W • BRIDGE MONO MODE 8 ohms 1 kHz 0.1% THD 2800W 4 ohms 1 kHz 1% THD 4000W |
£ Please phone EACH EX VAT & DELIVERY |
| |
QSC ISA 300T 2 x 300W – 100 volt line power amplifier with rear gain controls or 2 x 280W @ 4 Ohms power amplifier with rear gain controls • STEREO MODE, Both Channels Driven 70V or 100V 50 Hz-16 kHz 0.5% THD 300W 8 ohms 20 Hz-20 kHz 0.1% THD 185W 4 ohms 20 Hz-20 kHz 0.1% THD 280W 2 ohms 1 kHz 1% THD 430W • BRIDGE MONO MODE 8 ohms 1 kHz 0.1% THD 600W 4 ohms 1 kHz 1% THD 830W |
£ Please phone EACH EX VAT & DELIVERY |
| |
QSC ISA 500T 2 x 500W – 100 volt line power amplifier with rear gain controls or 2 x 425W @ 4 Ohms power amplifier with rear gain controls • STEREO MODE, Both Channels Driven 70V or 100V 50 Hz-16 kHz 0.5% THD 500W 8 ohms 20 Hz-20 kHz 0.1% THD 260W 4 ohms 20 Hz-20 kHz 0.1% THD 425W 2 ohms 1 kHz 1% THD 700W • BRIDGE MONO MODE 8 ohms 1 kHz 0.1% THD 900W 4 ohms 1 kHz 1% THD 1400W |
£ Please phone EACH EX VAT & DELIVERY |
| |
QSC ISA 800T 2 x 800W – 100 volt line power amplifier with rear gain controls or 2 x 650W @ 4 Ohms power amplifier with rear gain controls • STEREO MODE, Both Channels Driven 70V or 100V 50 Hz-16 kHz 0.5% THD 800W 8 ohms 20 Hz-20 kHz 0.1% THD 450W 4 ohms 20 Hz-20 kHz 0.1% THD 650W 2 ohms 1 kHz 1% THD 1200W • BRIDGE MONO MODE 8 ohms 1 kHz 0.1% THD 1500W 4 ohms 1 kHz 1% THD 2400W |
£ Please phone EACH EX VAT & DELIVERY |
AUDIO LIGHT SYSTEMS ARE MAIN DEALERS.
THE ABOVE UNITS ARE JUST A SMALL SELECTION OF THE RANGE, PLEASE CALL 0800 043 4600 FOR PRICING ON MORE MODELS. The images and specifications above are to give an overview of the design intent for the systems and components. They may not be the actual equipment supplied. Please contact Audio Light Systems for actual specifications, images and up to date costings. e&oe. |
||
